New: free Santa, snowman, tree, nutcracker and stocking charts →
Free chart

Learn / Cross stitch / Frame cross stitch

Cross stitch guide · updated 2026-11-10

How to frame cross stitch with a laced back

To frame cross stitch, center the clean, dry fabric over a suitable acid-free, lignin-free mounting board and lace the opposite fabric margins together on the back. Adjust the tension until the weave stays straight, then fit the mount into a frame deep enough for the layers. Use a window mat or frame spacers to keep the stitching clear of the glass.

MountingSewn lacing across opposite fabric margins
BoardSturdy acid-free, lignin-free board made for framing
GlazingKeep the stitches clear with a mat or spacers
Before cuttingCheck the design, visible border and frame's inner lip

Measure the stitched piece before buying a frame

Measure the actual stitching and decide how much plain fabric you want visible around it. Fabric count predicts the stitched area, but the frame opening must also accommodate your chosen border. A frame's lip hides a little of the mount, so test the visible opening rather than using only the size printed on the packaging.

For planning, design width in inches equals stitches divided by fabric count when each cross spans one Aida square. The Tiny Garden tulip is 11 by 14 stitches: about 0.79 by 1.00 inches on 14-count Aida. That is its design size, not its fabric cut size or frame size. Use our fabric size calculator and Aida count guide for another chart.

Gather the layers and check their depth

  • A frame with enough depth for the complete stack
  • Sturdy acid-free, lignin-free mounting board, cut to fit the frame
  • Clean cotton lacing thread, a needle, scissors and temporary rust-resistant pins if needed
  • A window mat or suitable frame spacers when using glass
  • A suitable backing board and the frame's retaining hardware

Keep ordinary cardboard, masking tape and glue away from the stitching. Lacing lets you adjust the fabric and remove the mount later. For valuable or fragile work, ask a framer experienced with textiles to choose and fit the materials.

Mount the fabric square, without pulling it tight

Prepare the piece with our washing and pressing guide if its materials allow it, and let it dry completely. Keep enough unstitched fabric to wrap around the board and take the lacing; do not trim it close to the design. Test the folds on the actual board before cutting anything.

Place the stitching face down on a clean surface and center the board over it. Fold one pair of opposite margins onto the back. Lace from one margin to the other with cotton thread, taking small bites of fabric clear of its raw edge. Work gradually along the board. Fold and lace the other pair in a separate pass.

Turn the piece over often. The fabric should lie smooth, with its grid parallel to the board edges. Ease the lacing if the weave bows or the stitches stretch. Fold bulky corners neatly without cutting towards the stitching.

Two views of the back of the mount. First, the left and right fabric margins are folded onto the board as bands and laced together with one continuous zigzag thread; the top and bottom margins are still flat. Second, the top and bottom margins are folded over the laced sides and laced together with another zigzag. All lacing stays on the board.Lace opposite fabric marginsBack of the mount. Fold a pair of margins onto the board, then lace them in one zigzag.1Fold and lace the sidesBOARDtop margin, still flatbottom margin, still flatLace the left and right margins together in onezigzag. Keep the grid straight on the front.2Then top and bottomBOARDsides already lacedFold the top and bottom margins over thelaced sides and lace them the same way.
Two views of the back of the mount. First, the left and right fabric margins are folded onto the board as bands and laced together with one continuous zigzag thread; the top and bottom margins are still flat. Second, the top and bottom margins are folded over the laced sides and laced together with another zigzag. All lacing stays on the board.Lace opposite fabric marginsBack of the mount. Fold a pair of margins onto theboard, then lace them in one zigzag.1Fold and lace the sidesBOARDtop margin, still flatbottom margin, still flatLace the left and right margins together in onezigzag. Keep the grid straight on the front.2Then top and bottomBOARDsides already lacedFold the top and bottom margins over the lacedsides and lace them the same way.
Back of the mount: lace opposite fabric margins in one direction, then the other. The board sits behind the unstitched display area and the fabric wraps over its edges.

Fit glass, a mat or spacers, and the mounted work

Clean the glazing before assembly and remove lint from the fabric with care. Looking from the front, the stack is glass, a window mat or perimeter spacers, the mounted stitching, then backing. The gap must clear the highest stitch or bead; do not compress the work to make a shallow frame close.

A mat gives a visible border and creates separation. Spacers can create that gap when you want no visible mat. If you choose an open frame with no glass, the fabric is exposed to dust and handling. Hang either finish away from direct sun and damp areas.

Choose another finish when it suits the motif

A small round display may be easier to finish in an embroidery hoop. A narrow motif can become a soft bookmark. These are different ways to finish the same counted work; you do not need a new pattern or a new PDF.

Choose a practice motif from Tiny Garden or Tiny Woodland. For a larger wall piece, the Christmas Village Bookshop has its own existing chart page. Return to the cross stitch hub for the stitching basics.

Lace and frame, step by step

  1. Plan the opening Measure the real piece, choose the visible fabric border, and test the frame lip and depth with all the intended layers.
  2. Prepare the mount Use a suitable framing board that fits inside the frame. Center the fully dry stitching over it, following the fabric grain.
  3. Lace the first pair Fold opposite margins onto the back. Sew between them in a gradual zigzag, keeping the display side smooth.
  4. Lace the second pair Repeat across the other two margins. Adjust both passes until the weave is straight and the corners lie flat.
  5. Assemble and secure Fit clean glazing, the mat or spacers, the mounted stitching and backing. Secure with the frame hardware without pressing the stitches against the glass.

Questions

Should cross stitch touch the glass in a frame?

Keep a gap between the stitching and glass. Use a window mat or suitable frame spacers, and allow enough depth to clear raised stitches and embellishments.

How do I frame cross stitch without a hoop?

Wrap the fabric over a suitable mounting board and lace opposite margins together on the back. Then place that mount in a picture frame with the needed mat or spacers.

Can I glue cross stitch to the backing board?

For the method here, use sewn lacing. Adhesive can be difficult to remove from fabric and makes later adjustment harder. Ask a textile framer about materials for a piece you want to preserve.

How much spare fabric do I need for framing?

Enough to wrap around your actual board and leave a sound margin for lacing on the back. Board thickness and frame size vary, so test the folds before trimming the fabric.