New: free Santa, snowman, tree, nutcracker and stocking charts →
Free chart

Learn / Cross stitch / How to backstitch cross stitch

Cross stitch guide · updated 2026-11-10

How to backstitch cross stitch

Backstitch makes a continuous outline over cross stitch. Come up ahead of the previous stitch, then take the needle down at its endpoint to close the gap. Follow the chart's line positions, color and strand count, usually adding the outline after the full crosses.

PurposeOutlines, small details and lettering shown as lines on the chart
OrderUsually after the full crosses so the line stays visible
ThreadUse the separate backstitch instructions, not automatically the full-cross strand count
DirectionEach front stitch travels back to meet the previous stitch

Find the outline instructions first

Look for a line-style key as well as the symbol key. A line can run along a square edge, diagonally across it or through part of a square. Trace its endpoints against the grid. Do not assume every black line is black thread or that every line must be divided into one-square segments.

A chart's line key separates crosses from detail stitches; the chart-reading guide shows how. Practice the basic X stitch with the cross stitch hub.

Follow the numbered front and back path

Our practice line progresses to the right while each new front stitch points left. Come up at 1 and go down at 2; travel behind the fabric to come up at 3, then go down at 4, where the first stitch began. Repeat with 5 and 6. Use the same hole for 1 and 4, and for 3 and 6.

The separate back view uses the same hole positions, as if you could see through the fabric without flipping it. Dashed arrows show the travel from a down hole to the next up hole. This is a stitch exercise, not an outline added to one of our charts.

Front stitches run from 1 to 2, 3 to 4 and 5 to 6, each going back into the previous hole. On the back the thread travels ahead two holes, from 2 to 3 and from 4 to 5. Events 1 and 4 share a hole, as do 3 and 6.Backstitch: front and backNumbers are needle events: odd up, even down.Threadon the frontSolidfront: needle goes DOWN at the tipDashedback: needle comes UP at the tipAFront: stitch back21 / 43 / 651 to 2; 3 to 4; 5 to 6.Each stitch goes back to close the gap.BBack: travel ahead21 / 43 / 652 to 3; then 4 to 5.Same positions as the front.Holes 1 / 4 and 3 / 6 are shared: the needle comes up there once and goes down there later.
Front stitches run from 1 to 2, 3 to 4 and 5 to 6, each going back into the previous hole. On the back the thread travels ahead two holes, from 2 to 3 and from 4 to 5. Events 1 and 4 share a hole, as do 3 and 6.Backstitch: front and backNumbers are needle events: odd up, even down.Threadon the frontSolidfront: needle goes DOWN at the tipDashedback: needle comes UP at the tipAFront: stitch back21 / 43 / 651 to 2; 3 to 4; 5 to 6.Each stitch goes back to close the gap.BBack: travel ahead21 / 43 / 652 to 3; then 4 to 5.Same positions as the front.Holes 1 / 4 and 3 / 6 are shared: the needle comesup there once and goes down there later.
Solid arrows end at needle-down holes; dashed arrows end where the needle comes up. Shared holes carry both event numbers.

Turn corners without rounding them off

End a segment at the charted corner, then start the next segment in its new direction. Keep the line on top of the completed crosses and avoid catching a strand from a neighboring stitch. If the chart asks for an endpoint between Aida holes, use a fine sharp needle to separate the fabric fibers carefully rather than forcing a blunt needle.

For a long straight run, use the chart's indicated endpoints. At a bend, shorter segments preserve the shape. Pull only until the thread rests against the surface; extra tension can pucker the fabric.

Fix loose, thick or broken-looking lines

What you seeWhat to check
A heavy outline hides detailCompare the number of strands with the backstitch key.
A loop catches on the surfaceCheck for loose thread on the back, then ease the loop down without puckering the fabric.
A gap between segmentsCheck that the new stitch ends at the previous endpoint.
A diagonal looks steppedRecheck the line's actual start and finish instead of following square edges.

For twisted floss (stranded cotton) and uneven tension: cross stitch troubleshooting tips.

Practice without changing the chart

Use spare fabric to stitch the straight line in the diagram before trying an outline on a finished project. Choose the Tiny Woodland, Tiny Garden or Tiny Sweet charts for separate full-cross practice. Their preview shapes are not instructions to outline every edge. Add backstitch to a chart only where its key calls for it, unless you are deliberately making your own variation.

Make a short practice line

  1. Secure the thread Anchor the tail on the back. Use the chart's stated strand count when working on a design.
  2. Make the first segment Come up at 1, then go down at 2 to make the first solid segment in the diagram.
  3. Come up ahead Travel on the back from 2 to 3. Leave a gap equal to the practice stitch length on the front.
  4. Close the gap Go down at 4, the same physical hole as 1. Continue up at 5 and down at 6, sharing hole 3.
  5. Check and secure Check that segments meet and lie flat, then weave the tail beneath nearby stitches on the back.

Questions

Do you backstitch before or after cross stitch?

Usually after the full crosses, so the outline lies on the surface. Follow the design instructions if they specify a different order.

How many strands should I use for backstitch?

Use the backstitch strand count in the chart key. It can differ from the full-cross count. If you are testing your own outline, compare samples on spare fabric first.

Does every cross stitch pattern need backstitch?

No. Some designs use full crosses alone. Only stitch the outline shown in the key unless you want to change the design.

Is backstitch the same as running stitch?

No. Backstitch closes each gap by returning to the previous endpoint. A single pass of running stitch leaves spaces between the visible stitches.